Electricity Multi Channel Car DVR / Automatic Vehicle Mobile DVR 75Ω

Electricity Multi Channel Car DVR / Automatic Vehicle Mobile DVR 75Ω

Multi Channel Car DVR Description

• Power Led, electricity, light, when the system is in standby state, the power indicator lights flashing;

Status Led, electricity, light, when the system is recording, the power indicator lights flashing. This product

is the normal input voltage is 12V/24V.

(2) trigger line and manual keys can select the image in any way 4-way camera

(3)In Trigger state, hand the keys effectively. When you press the manual key "Quad" of orbutton,

the trigger is invalid, Undo "QUAD" trigger to be effective

(4) After triggering undo, image delay three seconds, and enters the standby state.

(5) the trigger condition, no priority, when the trigger line when more than two trigger, then the trigger line

corresponding channel full-screen image,only three seconds, and then jumps automatically split image screen.

(6) can connect up to four cameras, and automatically split video screen

(7) car camera powered by the device for easy wiring

(8) DVD navigation screen display is triggered by the "red line" switching equipment, wiring and display convenience

(9) Each image can be set to forward / mirroring respectively; RCA connectors can be configured to connect DVD

Technical parameters

★On-off system and Manual mode introduced:

1. Short press or long press (more than 1 second) SMT button boot, showing automatic segmentation of images,again, a short press or for a long time to press the SMT button to shutdown, the system enters standby mode, but the system still in the recording.

2. long press the SMT button to boot, short press button to switch image mode.

★ Host box with high integration technology, four cameras centralized power supply box by the host, thereby greatly reducing the tedious wiring during installation, in addition to four cameras captured the image signal after the hosts converted by a video cable and the navigation DVD of "AV" port connection

Wiring Diagram Installation

<DIP switch>

★ mirror DIP switch: 4 switches, achieve about Mirror: dial-up ON, mirroring; OFF Just dial down. As default.

★ Parking DIP switch: a switch (fifth), to dial ON, system startup power loss protection, voltage is not enough, the system automatically dial down dormancy; OFF, power loss protection cancel.

To achieve parking video surveillance, proposed to ON state.

Four-core trigger line description

Four-wire:

Line 1 (Green) is a front view of the trigger line, you can access the Front

Office assist lamp or other neutral switch,When triggered,

the system boot, revoked, the system standby

Line 2 (white) left, as the trigger line, then turn left at light positive

(when the electric pen test twinkling).When the trigger,

automatic full screen display,

Line 3 (yellow) to reverse the trigger line, then reversing light positive,

When triggered, the system boot, when withdrawn,

system standby,

Line 4 (blue) to the right, as the trigger lines (sparking when electric

pen test) then turn right at lights positive,When triggered,

automatic full screen

Frequently Asked Questions

Question 1: SMD Tact switch function?
A: Long press (more than 1 second), the device starts to work, automatic image display screen (the default screen is H), long press again, the device enters the standby state; (Note: Press 1 second, the device starts, but Car navigation display screen response time takes about 1 second.)
Short press (less than 1 second), single-screen and "field" screen to cycle;
Question 2: 4 trigger lines how to wire?
A: Line 1 (Green) is a front view of the trigger wire, before the next depending on the assist lamp or other neutral switch place; the 2nd line (white) left, as the trigger line, then turn left positive light; the 3rd line (yellow) to reversing trigger line, then reversing light positive; Line 4 (blue) to the right, as the trigger line, then turn right at lights positive
Question 3: How to connect car navigation screen?
A: The device video output line connected car navigation screen, reverse video input port, the red line equipment output port connected to the reversing vehicle navigation screen test line, some car navigation screen video input is automatically detected, so reversing the test line can be removed.
Question 4: Why is there no output device?
A: Please check whether the device POWER Power lamp blinks, and if yes, then the device into standby mode, the output is off, press the power switch on the remote control or press the patch trigger switch device is turned on, POWER light long bright, video output device.
Question 5: Why dial left or right turn lamp lights, equipment no image?
A: The equipment in standby mode, dial left or right turn lamp lights, is not shown, because the normal driving, the driver will often toggle turn signal, if activated every time the screen display, it will affect the driver's driving safety a. If you intend to observe the situation around, press and touch switch or remote control to open the key.
Question 6: about the camera connected to where?
A: The camera can be connected at the bottom of the rearview mirror, you can monitor the front direction, because the left and right front wheels are usually dead, rear wheel rearview mirror, the normal camera monitoring is not required.
Q 7: power input line device connected to where?
A: Red power cable ACC (ie car ignition point), black ground (or Ground). As signs Parking REC, red power cable can be connected to the car battery positive (Note: the 5th DIP switch to the top).

NOTE: Power Led, when energized, the lights lit; when the system enters standby mode, the power light flashes. Status status lights, video flashes, when not recording continuously. This product is the normal input voltage 9V ~ 36V (the parking monitor is 12.5V ~ 36V).

4ch car dvr

multi channel car dvr

Electricity Multi Channel Car DVR / Automatic Vehicle Mobile DVR 75Ω Images